Full Engine Rebuilds
Oil Changes & Fluid Flushes
Brake Pad & Rotor Replacement
Chain/Belt Replacement & Adjustment
Valve Adjustments & Tune-Ups
Motorcycle Builds
Custom Bike Builds (Chopper, Bobber, Caf�, Bagger)
Bike Restoration Projects
Street-to-Track Conversions
Full Theme Customizations
Oil and filter changes
Air filter replacement
Coolant flush
Brake inspection and bleeding
Chain/sprocket or drive shaft inspection
Battery check and replacement
Tire pressure check and rotation
Valve adjustment
Suspension tuning or rebuild
CV boot and joint replacement
Carburetor/fuel injection cleaning
Transmission servicing
Clutch replacement
Oil change (engine, transmission)
Air filter cleaning or replacement
Chain cleaning, lubrication & adjustment
Spark plug inspection/replacement
Coolant flush and refill
Brake fluid flush
Fuel system check (carburetor/fuel injector cleaning)
Valve adjustment
Top-end rebuild (piston, rings, gaskets)
Bottom-end rebuild (crankshaft, bearings)
Clutch inspection and replacement
Suspension servicing (fork seals, oil, shock rebuild)
Wheel bearing and swingarm bearing replacement
Jetting/tuning carburetor
ECU remapping/tuning
Aftermarket exhaust installation
High-performance air filter
Suspension tuning/customization
Sprocket and gear ratio changes
Tire replacement and balancing
Spoke tightening and wheel truing
Chain and sprocket replacement
Brake pad and rotor replacement
Handlebar, lever, and control adjustments
Pressure washing
Degreasing engine and drivetrain
Plastic and graphics restoration
Seat cover replacement or repair
Bolt/nut torque check
Brake function and fluid level check
Tire pressure check
Control cable lubrication and inspection
Lights and electrical check (if equipped)
Oil Change
Replace engine oil and oil filter
Check for leaks or contamination
Air Filter Service
Clean or replace engine air filter
Clean or replace CVT intake/exhaust filters
Fluid Checks and Changes
Transmission fluid
Front and rear differential fluid
Coolant level and quality
Brake fluid flush (as needed)
Battery Service
Test battery health and charge
Clean terminals
Replace battery if needed
Spark Plug Inspection/Replacement
Check for wear, fouling, and proper gap
Belt Inspection (CVT)
Inspect for cracking, glazing, or excessive wear
Replace if needed
Brake Inspection
Inspect pads, rotors, and lines
Replace worn parts
Tire Service
Check tire pressure
Inspect tread and sidewalls for damage or wear
Rotate tires
Greasing and Lubrication
Grease all suspension and steering zerks
Lubricate pivot points and joints
Suspension and Steering Check
Inspect shocks, bushings, ball joints, tie rods, and control arms
Valve Adjustment (for some models, especially sport UTVs)
Cooling System Flush
Fuel System Cleaning (injector cleaning or fuel additive)
Clutch Inspection and Cleaning (important for CVT-equipped models)
Chassis and Frame Inspection (check for cracks, stress, or rust)
ECU tuning or software updates
Winch maintenance or install
Light bar or accessory wiring
Snorkel kit install for deep water use
Skid plate or armor upgrades
Shock re-valving or upgrade
Tire upgrade (beadlocks, paddle tires, etc.)
(May vary per brand/model � always refer to owner�s manual)
Every 25 hours or 250 miles: oil/filter, fluid checks, air filter
Every 50 hours or 500 miles: spark plugs, belt, CVT service
Every 100 hours or 1,000 miles: diff fluids, brake flush, valve check
Diagnostics & Inspections
Pre-Ride Safety Checks
Compression & Leak-Down Tests
Ride-In Diagnostics
Used Bike Inspection Services
Frame Modification & Welding
Hand-Fabricated Brackets & Mounts
Custom Paint & Powder Coating
One-Off Parts Fabrication
Electrical Services
Full Rewiring & Troubleshooting
Lighting Upgrades
Ignition System Diagnosis
Alarm & GPS Installations